Repair guide

Washing Machine Shaking and Moving? Here’s Why

Practical fixes from Al‑Haram's Abu Dhabi technicians, and when to call a pro.

Washing Machine Shaking and Moving? Here’s Why, Al Haram Electrical Appliances Repairs Shop, Abu Dhabi

Why your washing machine is shaking and moving: the usual causes

CauseHow to tellWhat fixes it
Unbalanced loadShaking starts only on spin and changes from load to load. Often one heavy item, such as a rug, has bunched up.Stop the machine, spread the clothes evenly and spin again.
Machine not levelThe machine rocks when you press opposite top corners. A spirit level shows it leaning.Adjust the screw feet at the front and lock them with their nuts.
Transit bolts still fittedA new machine or one just moved to a new home shakes violently from the first spin. Bolts are visible at the back.Remove the transit bolts with a spanner and fit the plastic caps supplied.
Soft or uneven floorThe floor flexes, the tiles slope, or the machine sits on a loose stand or wooden board.Move the machine to a solid, flat floor or fit a sturdy, level base.
Worn shock absorbersThe drum drops easily and bounces when pushed down. Shock absorbers, also called dampers, slow the drum’s movement.A technician replaces the dampers, usually as a pair.
Broken suspension springThe drum hangs lower on one side or bangs against the cabinet.A technician refits or replaces the spring that holds the drum up.
Worn drum bearingsA loud rumble like a jet engine on spin, and the drum feels loose when you lift its edge.A technician replaces the bearings and drum seal, or advises replacement on an old machine.

How to fix a washing machine that shakes, step by step

  1. Unplug the machine and turn off the water tap before you move or tilt it.
  2. Check for transit bolts. If the machine is new or was moved, look at the back panel for three or four large bolts. Remove them and keep them for your next move.
  3. Level the machine. Put a spirit level on top, front to back and side to side. Turn the front feet to raise or lower each corner, then tighten the lock nuts.
  4. Check it does not rock. Press down on opposite top corners. If it rocks, adjust the feet again until all four sit firmly.
  5. Check the floor. Take away any mat, board or loose stand under the machine. It should stand on a hard, flat floor.
  6. Test the suspension. Open the door and push the drum down firmly, then let go. It should move back and settle quickly. If it bounces several times or knocks, the dampers or springs are worn.
  7. Run a test spin with a medium, mixed load. Avoid single heavy items. If it still shakes hard, stop and call a technician.

If the shaking comes with a drum that will not reach full speed, read our guide on a washing machine not spinning.

When to stop and call a technician

  • The machine walks far enough to stretch its hoses or power cable.
  • You hear loud banging, grinding or a rumble that gets louder each week.
  • The drum sits lower on one side or hits the cabinet.
  • Water appears under the machine together with the shaking.
  • You see rust streaks or black powder under the drum area.

Dampers, springs and bearings sit inside the cabinet and the drum is heavy. Al Haram Electrical Appliances Repairs Shop repairs this at home across Abu Dhabi, usually the same day. Our experienced technicians carry common parts for washing machine repair in Abu Dhabi. Call or WhatsApp +971 50 699 7974, daily from 8 AM to 10 PM.

Shaking and Abu Dhabi homes

Many Abu Dhabi families move between apartments, and transit bolts are easily forgotten after a move. Smooth porcelain tiles also give rubber feet little grip, so a slightly unbalanced machine slides more easily.

In apartment towers, a shaking machine on an upper floor carries noise through the building, and neighbours notice it late at night. Machines placed on raised plinths or stands on roofs and service yards need extra care, because a stand that flexes makes every spin worse.

How to stop it happening again

  • Wash heavy items like bath mats and blankets with a few smaller pieces.
  • Check the level and the lock nuts on the feet every few months.
  • Do not overload the drum or wash a single heavy item alone.
  • Keep the transit bolts and refit them before any move.

Related repair guides and services

Washing machine shaking: your questions answered

Is it dangerous if my washing machine shakes a lot?
Al Haram Electrical Appliances Repairs Shop technicians warn that heavy shaking can be a risk. The machine can pull its hoses loose, causing a flood, or stretch the power cable. Constant hammering also wears out dampers, springs and bearings quickly. Stop the cycle, level the machine and spread the load before using it again.
What happens if I run a washing machine with the transit bolts in?
At Al Haram Electrical Appliances Repairs Shop, we see this often after house moves. Transit bolts lock the drum for transport. If you spin with them in, the machine shakes violently and can damage the drum, springs, dampers and bearings. Remove the bolts before the first wash and fit the plastic covers supplied.
Should I repair or replace a washing machine that shakes?
According to Al Haram Electrical Appliances Repairs Shop, levelling and load problems cost nothing to fix. Dampers and springs are a routine repair. Worn bearings are a bigger job, and on an older machine replacement may be wiser. The price depends on the part, and our technician quotes it after diagnosing the machine at your home.
Why does my washing machine walk across the floor on spin?
Al Haram Electrical Appliances Repairs Shop usually traces this to a machine that is not level, an unbalanced load or slippery tiles. Uneven feet let the machine rock, and each rock moves it a little. Level all four corners, tighten the lock nuts and spread the load. If it still walks, check the shock absorbers.
Still stuck? If these steps don't fix it, Al‑Haram offers same-day repair across Abu Dhabi. Call or WhatsApp +971 50 699 7974 and we'll take it from here.
Call nowWhatsApp